Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does a Gate Motor & Opener Cost in Virginia Beach?
Most gate motor and opener work in Virginia Beach runs $450 to $2,800 for a repair, and a full new opener installation typically lands between $1,600 and $9,000 depending on the operator class. A basic diagnostic and adjustment visit is usually the smallest ticket at $150 to $350. The written estimate you get after we look at the gate sets the final price, and that estimate is free.
Gate automation isn’t a single product with a single price. A residential driveway swing operator and a commercial slide operator on a managed property sit at opposite ends of the market, and the failure that brought you to this page matters just as much as the brand on the control board. What follows is a straight breakdown of what each piece of work tends to cost in Virginia Beach, what pushes it up or down, and how to avoid paying for a system you don’t need.
Key Takeaways
- Opener replacement on a residential gate in Virginia Beach typically runs $1,600 to $4,200 installed.
- Control board and receiver repairs are usually $250 to $700, and we handle board-level faults from LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule.
- Safety sensor, loop detector, and keypad work is priced separately and usually falls in the $200 to $650 range.
- Diagnostics and adjustment visits start around $150, and the estimate is free.
- Our technicians have up to 14 years of experience, and every job is quoted per gate after an on-site look.
Gate Motor & Opener Cost Breakdown (2026)
Here’s how the pieces break out. These are typical ranges for work in Virginia Beach this year, not exact quotes. Your gate’s weight, travel, power source, and operator class will move the number within the range, and the written estimate is what you can hold us to.
| Work | Typical Virginia Beach range | What it usually covers |
|---|---|---|
| Diagnostic and adjustment visit | $150 – $350 | Full inspection, travel and limit adjustment, sensor alignment, written report |
| Control board replacement | $350 – $700 | Board, programming, and reconnecting accessories |
| Receiver and remote pairing work | $200 – $400 | Replacement receiver, remote programming, range testing |
| Safety sensor or loop detector replacement | $250 – $650 | New photo-eye set or in-ground loop, wiring, and calibration |
| Keypad or access control replacement | $300 – $800 | Wired or wireless keypad, phone entry, or card reader integration |
| Operator replacement, residential swing or slide | $1,600 – $4,200 | New arm or slide operator, brackets, wiring, and programming |
| Operator replacement, commercial or high-security | $4,500 – $9,000 | Commercial-grade operator, access control integration, safety devices |
| New automated gate installation | $5,000 – $14,000 | Gate, operator, power run, safety devices, and access hardware |
The operator itself is often the smaller part of the bill. What moves the total up is what sits around it: how far power has to travel, whether the driveway is paved or gravel, whether the gate is a heavy metal slide panel or a lighter residential swing, and how many access points the property needs. A property manager who wants keypad entry, vehicle loops, and remote monitoring for a commercial lot is buying a different scope of work than a homeowner who wants one remote and a photo-eye set. Cross-brand fluency matters here, because we work on the gate you have rather than the one we prefer to sell. Diagnosing a DoorKing control board and diagnosing a Mighty Mule arm take different knowledge, and both get handled on-site.
What Affects Gate Motor & Opener Pricing in Virginia Beach
- Operator class. A residential Mighty Mule or Ghost Controls arm and a commercial FAAC or BFT operator are priced very differently, because the components, duty cycle, and safety requirements differ. A system built to cycle dozens of times an hour costs more to service than a driveway gate that opens twice a day.
- Gate weight and travel. Heavier panels and longer travel runs load the operator harder, and replacing the motor on a wide slide gate means matching the operator to the load, not simply swapping boxes.
- Power source and distance. If power isn’t already at the gate, running it adds real cost. A gate set 80 feet from the nearest outlet is a straightforward job; one set back off a long rural driveway needs more conduit, wire, and planning.
- Access control scope. Keypads, loop detectors, intercom systems, and card readers are separate line items. A residential gate with one remote is a different total than a commercial property with a managed entry system.
- Safety devices. Photo-eyes, edge sensors, and other entrapment protection are part of a compliant installation and are priced in. Skipping them to save money isn’t a saving, and we won’t quote a job that leaves a moving gate without proper protection.
- Brackets, mounting, and site conditions. On a slide or swing gate, worn hinges, a shifting post, or a bent track can affect what the motor has to overcome. Those are separate from the operator and priced after the site visit.
The brands on your operator don’t change whether we can work on it. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, which covers most of what’s on gates across Virginia Beach. If your property has a brand not on that list, tell us when you call and we’ll tell you honestly whether we’re the right fit before you commit.
How to Save on Gate Motor & Opener Work in Virginia Beach
The largest saving on any gate job is catching the failure before the motor dies. A control board that’s tripping on a dragging gate or a misaligned photo-eye set will end up burning out the operator over time, and replacing a sensor is much less than replacing a motor. Have the gate adjusted when it starts to drag or reverse unexpectedly.
- Diagnose before you replace. A dead gate is often a receiver, a sensor, or a program fault, not a dead motor. We diagnose board-level faults and tell you what actually failed before recommending a replacement.
- Batch small jobs into one visit. If the keypad is flaky and the photo-eyes keep tripping, bundle them. One trip and one estimate usually costs less overall than two.
- Ask about the current operator’s service life. If a motor has years left, repairing it is almost always cheaper than replacing the whole unit. We’ll give you the honest answer.
- Keep the gate itself clear. Clogged tracks, vegetation, and loose hinges force the operator to work harder and shorten its life. Clearing the travel path is free.
- Get the free estimate in writing. That way the scope and price are agreed before anyone touches the gate.
Free estimates are exactly that. Call (844) 834-3028 and we’ll look at the gate, tell you what’s actually wrong, and give you a written price for the repair or replacement. No surprise fees when the work is done.
When Does It Make Sense to Replace Rather Than Repair the Opener?
Replacement usually makes sense when the operator is over its service life, when the board is no longer made and used parts are unavailable, or when the class of operator no longer matches what the gate needs. A residential arm on a gate that’s grown heavier over the years, or an older board with no parts support, both point toward a new operator. Below that line, repair almost always comes out cheaper.
As a rough guide, if a repair quote comes in at more than about half the cost of a comparable new operator installation, replacement is usually the more sensible spend. If it’s a control board, a sensor, or a keypad on a motor with life left in it, repair wins. You’ll get a clear recommendation from us, in writing, before anything is ordered.
FAQs – Gate Motor & Opener Cost in Virginia Beach
How much does it cost to replace a gate motor in Virginia Beach?
Gate motor replacement in Virginia Beach typically runs $1,600 to $4,200 for a residential swing or slide operator, and $4,500 to $9,000 for a commercial or high-security operator. The difference comes down to operator class, duty cycle, access hardware, and how power reaches the gate. We work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so we can quote the replacement against the operator that’s actually on your gate. Call (844) 834-3028 for a free on-site estimate.
Can you repair my gate operator the same day?
Many common faults, including photo-eye misalignment, remote pairing problems, and limit adjustment, are handled on the first visit in the same afternoon or morning. Board-level failures and operator swaps sometimes need a part ordered, which means a return visit. When you call, tell us the gate type and the brand on the control board, and we’ll give you a realistic picture. Fast dispatch is 7am to 7pm, Sunday through Friday, and we answer the phone 24/7.
Is it cheaper to repair or replace a gate opener in Virginia Beach?
Repair is almost always cheaper, usually $200 to $800 versus $1,600 and up for a new operator. Replacement becomes the better call when the board is discontinued, the operator is beyond its service life, or the gate has grown heavier than the arm was built for. If the repair quote comes in at more than half the cost of a new install, replacement usually wins. Call us and we’ll tell you which side of that line your gate sits on.
How much does a new automatic gate cost in Virginia Beach?
A new automated gate installation in Virginia Beach typically falls between $5,000 and $14,000, including the gate, operator, power run, and safety devices. That range covers both residential driveway gates and small commercial access points. The parts that move it most are gate material and weight, pavement, and the access control hardware. For an exact figure on your property, call (844) 834-3028 and we’ll walk the site with you.
Do you work on my brand of gate opener?
We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, which covers most residential and commercial gate operators in Virginia Beach. If your gate has a brand or model outside that list, tell us on the call and we’ll tell you honestly before booking. Our technicians have up to 14 years of experience across both residential-grade and commercial access control systems, and we diagnose on-site rather than routing work to another trade.
Getting a Straight Price for Your Gate in Virginia Beach
Gate pricing isn’t something we can quote blind, and any number you get over the phone without an on-site look is a guess. We’d rather give you a real figure based on the actual gate, the actual operator, and the actual fault. That’s the difference between a repair that lasts and one that fails again in a season.
If you have a gate that’s stopped responding, a gate that reverses unpredictably, or a gate that’s due for an operator replacement, call us. We’re dedicated gate specialists, and every visit is built around diagnosing what’s wrong and quoting the right fix, not upselling a brand switch. Call (844) 834-3028 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Pricing reflects the Virginia Beach market as of 2026. Ashton Gate Repair offers free estimates – call (844) 834-3028.
Written by the team at Ashton Gate Repair.
What Our Customers Say
"Gate stopped halfway and sat there for two days blocking the driveway. He found a dead capacitor in the operator, swapped it, and we were moving cars again in under an hour."
- Malik Nash"The loop detector under the driveway had failed and residents were stuck holding the button. He traced it, found the break, and had the exit loop reading cars again the same visit."
- Simone Boyd"Fixed the immediate problem. He was honest that the operator is near end of life and I should budget for a replacement, which I appreciate even if it wasn't what I wanted to hear."
- Tracy Miller